These are the 7 Shark Bites you must buy - Writers Evoke
Business

These are the 7 Shark Bites you must buy

Shark Bites plumbing fittings are a do-it-yourself plumber’s miracle. They are also expensive . If you don’t mind bargaining a few dollars for convenience, they are a must.

Among the hundreds of products in the Shark Bite catalog, there are a few that you will use over and over and over again. These 7 Shark Bites, in order of importance, will take care of most of your small to medium DIY plumbing remodels and will solve the confusion about how to install shark bite valve on copper. All work with pipes PEX, copper or CPVC.

What it does : Makes a straight line connection between two wired water supply hoses.

Why do you need it ? When you can cut leaky and leaky copper pipe , straight fittings help you make the transition from pipe to pipe smoothly. It’s also a great way to lengthen the PEX tubing you are already using, rather than dealing with long continuous runs.

Specifications: Shark Bite U008LFA

  • Shark Bite 1/2 “by 1/2” by 1/2 “Tee
  • Shark Bite half-length tee-shirt. via Amazon

What it does: Connect two 1/2 “lines in a straight line, with an additional third 1/2” line leading at a 90 degree angle. For bypass supply pipes.

Also Read  How to Choose the Right Printer for Your Small Business

Why You Need It?: This Shark Bite Tee allows you to interrupt a straight PEX or other pipe and shoot in another direction to serve another area. For example, you can “clear” and tie in a toilet, shower, tub, sink, etc.

Specifications: Shark Bite U362LFA

  • Shark Bite 1/2-Inch Elbow
  • Shark Bite 1/2 “Elbow via Amazon

What it does: Connect two branch supply hoses at a 90 degree angle.

Why You Need Them: Half-inch elbows are extremely functional, and you can’t have too many around. Not enough room to turn your pipe a half inch with a five inch spoke rack? No problem. Elbows allow you to send the pipe in a different direction in a limited space.

Specifications: Shark Bite U248LFA

  • Shark Bite Ball Valve 1/2 “
  • Shark Bite half-inch ball valve. via Amazon

What it does : 

Ball valves shut off the flow of water in the bypass supply pipe – but farther down the line than at the main water shutoff valve .

Why you need it : Installing a ball valve allows you to demarcate plumbing areas, isolating them from the main water system. For example, you can have a reworked basement that you want to control separately from other areas.

Ball valves are particularly suitable for areas known to have their problems, such as outdoor hose taps or laundry rooms. In the event of an emergency leak, you can quickly stop the leak only in that area, while still maintaining  plumbing problems the flow of water to the rest of the house.

Specifications : Shark Bite 22222-0000LF

  • Shark Bite 1/2 ” End Cap
  • Shark Bite half-inch bit via Amazon
Also Read  Benefits of Hiring Professional Brickwork Contractors:

What it does : End caps provide a way to close the end of a single limb supply hose. They’re like a door at the end of a long hallway, except it’s basically a permanently closed door. Why you need it : You won’t need a lot; maybe one or two. Ferrules are a good way to stop a pipe when you are in the middle of a plumbing remodel.

Data sheet: Shark Bite U514LFA

  • Shark Bite 3/4-Inch by 3/4-Inch by 1/2-Inch Reduction Tee
  • Shark Bite 3/4 x 3/4 x 1/2 Reducer Tee. via Amazon

What it does : Reducing tees tap into the flow of a line of a certain diameter, sending out a third line of a smaller diameter. In this case, two 3/4 “lines continue in and out of the tee, with a third 1/2” line drawing at a 90 degree angle.

Why You Need It : 

These 3/4 “to 1/2” reducing tees “convert” your main water line (the one coming from the street to the water heater) and send it to various services that need it. cold water: sinks, toilets, etc.

Data sheet: Shark Bite U412LFA

  • 3/4 “Shark Bite Ball Valve
  • Shark Bite 3/4 “Ball Valve via Amazon

What it does : Like the Shark Bite 1/2 “ball valve, this one shuts or stops a water line, in which case the 3/4” ball valve breaks in your line. main water.

Why You Need It : If you have a bad valve at the point where water enters the street, this ball valve replaces it.

It can also be used in an emergency to shut off a 3/4 “water line that is flooding your home Cut the 3/4” garden hose. Slide this ball valve with the lever turned in the “Open” direction. Then, once the SharkBite is fully installed, close the valve.Specifications : SharkBite 22185-0000LF

Also Read  6 questions to ask before you hire a Plumber
Show More

Related Articles

Leave a Reply

Back to top button

Adblock Detected

Please consider supporting us by disabling your ad blocker